A butt joint is a wood joint in which the end of a piece of material is simply placed (or “butted”) against another piece. The butt joint is the simplest...

of joints referred to by the American Welding Society: butt, corner, edge, lap, and tee. These types may have various configurations at the joint where...

Butt welding is when two pieces of metal are placed end-to-end without overlap and then welded along the joint (as opposed to lap joint weld, where one...

Look up butt or Butt in Wiktionary, the free dictionary. Butt may refer to: Butt (magazine) The Butt, a 2008 novel by Will Self Der Butt, German title...

small rod is used internal to a joint both to help align and to strengthen the joint. Traditional joints such as butt joints are used with natural timbers...

joints such as the butt joint and the splice joint and is often favored over these in joinery because it yields a barely visible glue line. The joint...

alternative to other joints such as the butt joint and the scarf joint. Splice joints are stronger than unreinenforced butt joints and have the potential...

types of weld joints are the butt joint, lap joint, corner joint, edge joint, and T-joint (a variant of this last is the cruciform joint). Other variations...

strong bond, stronger than a butt joint but not very visually appealing. Finger joints are regularly confused with box joints, which are used for corners...

As a jointer, the machine operates on the narrow edge of boards, preparing them for use as butt joint or gluing into panels. A planer-jointer setup has...

vertical side casings where the elements join (forming a butt joint, as opposed to a miter joint). In an entablature in classical architecture, it is the...

connector (also called a butt-joint fastener) often used in scenic construction to join together stage decks or scenery in a butt joint. These are two part...

a normal butt joint. Eg: Internasal suture. Limbous sutures – edges are bevelled so the plane of the suture is sloping as in a mitre joint. Eg: Temporo-parietal...

securing a weld-on pivot link is a [t weld] which consists of a perpendicular vee butt joint secured to the billet using a butt weld or fusion weld....

joint surface. Butt Joint Flash Trap (Internal) - The bead is covered by a rib or flash trap. Butt Joint Flash Trap (External) - This type of joint hides...

the grease gun end latches onto the nipple and sealing is effected as a butt joint. If this type of gun end is not perfectly aligned with the nipple, they...

Cast-Welding of Rail Joints. Street Railway Review, Vol. 4, Windsor & Kenfield Publishers, Chicago, 1894. The Cast Welded Joint. The Street Railway Review...

and dowlis of tho wheelis..." Bar stock Barrel nut Dowel reinforced butt joint Dowel bar retrofit Fastener Kinematic coupling Rebar Spring pin Threaded...

with a shorter ferrule, a thicker butt and joint, a wooden joint pin (ideally) and collarless wood-to-wood joint, a conical taper, and a smaller tip...

different rates. The mating sections are tapered diagonally (unlike a butt joint between two lengths of rail), allowing smoother transitions and higher...

typically comprise several planks which are either scarfed, or butt-jointed and reinforced with a butt block. Where the transverse sections of the vessel's shape...

The cross-section of a welded butt joint, with the darkest gray representing the weld or fusion zone, the medium gray the heat-affected zone, and the lightest...

joint. Another frequently used term is 'doobie.' The end or butt of a mostly smoked joint is referred to as a "roach" in U.S. and Australian slang. Small...

perpendicularity is not always ideal or even achievable, unless welding a horizontal butt joint.  Therefore, the gun will usually be oriented so the wire bisects the...

various styles of joining the pieces, from board and batton, where the butt joints between panels is covered with a thin strip (usually 25 to 50 mm wide)...

countertops. In a mason's mitre, the two elements being joined meet as for a butt joint but a small section of one member is removed creating a socket to receive...

three-piece implant the abutment is fixed on the implant with a screw butt joint. This screw needs to be tightened to a predetermined torque with a dental...

the faying surfaces of two similar metals. The seam may be a butt joint or an overlap joint and is usually an automated process. It differs from flash welding...

several methods: cope and stick, mortise and tenon, bridle joint, or a simple butt joint. Cope and stick is the most common method, as it is more efficient...

bending test, this method is more suitable for strength evaluation of butt joint specimens. The advantage of four-point bending test is that a larger portion...