results in a smaller wear scar is considered to have higher lubricity. For this reason, lubricity is also termed a substance's anti-wear property. Examples...

adjusted without breaking or untying the strand. Dyneema/Spectra's very high lubricity leads to poor knot-holding ability and has led to the recommendation to...

alloy that can increase lubricity. The process used to reduce the sulfur also reduces the fuel's lubricating properties. Lubricity is a measure of the fuel's...

Evaluating Lubricity of Diesel Fuels by the High-Frequency Reciprocating Rig (HFRR)". www.astm.org. Retrieved 2018-08-08. "HFRR best test for lubricity". www...

requirements over FA with regard to lubricity, detergency, exhaust smoke and exhaust system blocking. JASO FC – lubricity and initial torque requirements...

fuel's quality include (but are not limited to) energy content, density, lubricity, cold-flow properties and sulfur content. The cetane number of a fuel...

(high crystalline) the better the lubricity and resistance to oxidation. For applications where only a minor lubricity is needed and a more thermally insulating...

content ≤10 mg·kg−1 ≤10 mg·kg−1 Water content ≤200 mg·kg−1 ≤500 mg·kg−1 Lubricity 460 μm 460 μm Viscosity at 40 °C 2.0...4.5 mm2·s−1 3.5...5.0 mm2·s−1 FAME...

or cooling the surfaces. The property of reducing friction is known as lubricity. In addition to industrial applications, lubricants are used for many...

chemically different "esters" due to their polarity and usually excellent lubricity are used for various reasons as either "additives" or "base stocks" for...

of the most important additives include those used for viscosity and lubricity, contaminant control, for the control of chemical breakdown, and for seal...

Challenges with using gasoline in a PPC engine arise due to the low lubricity of gasoline and the low cetane value of gasoline. Use of fuel additives...

to 1,000 ppm, which therefore means it has better lubricity and does not currently require a lubricity additive as all pipeline diesel fuels require.[citation...

cetane index is not specified in MIL-DTL-83133G to 40 or higher. Because lubricity to the BOCLE method is not specified in MIL-DTL-83133G, modern common-rail...

and outboard motors, and was established in 1994. For 2-stroke oil, lubricity, cleanliness, exhaust smoke, and exhaust system blockage are evaluated...

the decal the ability to slide off the paper and onto the substrate (lubricity). Water slide decals are thinner than many other decorative techniques...

the fat will penetrate it to varying degrees, contributing richness, lubricity, its own flavour, and calories. Frying techniques vary in the amount of...

retention. Others manufacture blades that are polymer-coated to enhance lubricity during a cut. Scalpels may be single-use disposable or re-usable. Re-usable...

aliphatic chains then line up towards the outside of the fiber, imparting lubricity. Fabric softeners impart anti-static properties to fabrics, and thus prevent...

compounds. Lubricity of fuel plays an important role in wear that occurs in an engine. A diesel engine relies on its fuel to provide lubricity for the metal...

1–100 μm is a common dry lubricant. Few alternatives exist that confer high lubricity and stability at up to 350 °C in oxidizing environments. Sliding friction...

whale oil was used annually in lubricants because of its exceptional lubricity and heat stability. In 1972, the sperm whale was listed as an Endangered...

candies; research shows that "hard, round foods with high elasticity or lubricity properties, or both, pose a significant level of risk," especially to...

applications needing high temperature stability, very low volatility, inherent lubricity, and/or radiation resistance. Perfluoropolyether oils are their more chemically...

with a range of temperatures and shear rates. The generic device records lubricity, plasticity, scorch, cure, shear, and heat stability. Perhaps the most...

Manganese phosphate coatings are used both for corrosion resistance and lubricity and are applied only by immersion. Iron phosphate coatings are typically...

affect surface energy, adhesion, biocompatibility, chemical inertness, lubricity, sterility, asepsis, thrombogenicity, susceptibility to corrosion, degradation...

The process of removing sulphur from the fuel impacts the viscosity and lubricity of the marine gas oil though, which could cause damage in the engine fuel...

000 psi (2.14 GPa), higher than of a hydraulic oil at room temperature. Its lubricity is poor, so positive-displacement pumps are unsuitable and centrifugal...

and rigidity, and molybdenum disulfide-filled variants which increase lubricity. Nylon can be used as the matrix material in composite materials, with...