A riser, also known as a feeder, is a reservoir built into a metal casting mold to prevent cavities due to shrinkage. Most metals are less dense as a liquid...

then it is known as a top riser and if it is located next to the casting it is known as a side riser. Finally, if the riser is located on the gating system...

the deck Riser, the center section of a recurve bow Parachute riser, strip of webbing joining the harness to the rigging lines Riser (casting), a reservoir...

Die casting is a metal casting process that is characterized by forcing molten metal under high pressure into a mold cavity. The mold cavity is created...

the runner system to the casting cavity. Gas and steam generated during casting exit through the permeable sand or via risers, which are added either in...

and risers that enable the metal to fill the mold. The mold and the metal are then cooled until the metal solidifies. The solidified part (the casting) is...

chill can be used to increase the feeding distance of a riser or reduce the number of risers required. Chills can be made of many materials, including...

punching, forging, or machining. Internal scrap consists of gates, risers, defective castings, and other extraneous metal oddments produced within the facility...

the sprues, gating systems, and risers are placed with respect to the pattern. Where a hole is desired in a casting, a core may be used which defines...

Steel casting is a specialized form of casting involving various types of steel cast to either final/net or near-net shape. Steel castings are used when...

and the sand removed to reveal the rough casting. The rough casting is separated from the sprue and riser(s) either by sawing them off, or just breaking...

because there is no riser and any metal in the pouring tube just falls back into the ladle for reuse. The vast majority of LPPM casting are from aluminum...

valve boxes, covers and risers. These products are covered by the Buy America Act of 1982. "By law, American-made municipal castings must be used in many...

gases as well. In general, microporosities will form if the casting is not properly risered or if a material with a wide solidification range is cast....

[J·kg−1·K−1]). It is most useful in determining if a riser will solidify before the casting, because if the riser solidifies first then defects like shrinkage...

In many cases it controls the flow of material into the mold. During casting or molding, the material in the sprue will solidify and need to be removed...

Lost-foam casting (LFC) is a type of evaporative-pattern casting process that is similar to investment casting except foam is used for the pattern instead...

Low-riser intake, 2x4V 12:1 — 425 horsepower (317 kW) at 6000 rpm and 480 lb⋅ft (651 N⋅m) at 3700 rpm 1964 Ford Fairlane Thunderbolt, Mercury: High-riser...

Semi-solid metal casting (SSM) is a near net shape variant of die casting. The process is used today with non-ferrous metals, such as aluminium, copper...

As compared to investment casting, it is cheaper because it is a simpler process and the foam is cheaper than the wax. Risers are not usually required...

revealing an image of the wax form, including core pins, sprues, vents, and risers. All of these are removed with a saw and tool marks are polished away, and...

replace natural food sources Feeder (casting), another name for a riser, a reservoir built into a metal casting mold to prevent cavities due to shrinkage...

Mrs. Parker Demetrius Navarro as Hector Reynaldo Rey as Red's father Ronn Riser as Stanley Justin Revoner as Kid #1 Meagan Good as Kid #2 Terri J. Vaughn...

as surrounding areas because there is less heat flow; this is called a riser effect. Also note that corners can create divergent or convergent (also...

many musicians treat more personally. Risers—a riser is a raised area of stage, the size and positioning of risers for musicians (such as drummers, orchestra...

vibration caused through riding. Riser pads are normally made of plastic. Shock pads, which are more rubbery than riser pads, serve the same function only...

| High-Def Digest". Riser, James (6 February 2011). "Film Review: The Dunwich Horror (2009)". HorrorNews.net. James Patrick Riser. Retrieved 27 July 2016...

6061-T6 is used for: bicycle frames and components middle to high-end recurve risers many fly fishing reels. the Pioneer plaque the secondary chambers and baffle...

Eagle Guard Rosemary Alexander as an Eagle Guard Steve Alterman as Late Riser Bird, a bird who serves as a waiter/Additional Voices. Steve Apostolina...

push up against. Visual effects then removed the special effects team and riser from the shots. The 1982 Broxton, Oklahoma McDonald's location was filmed...