A rocker arm is a valvetrain component that typically transfers the motion of a pushrod in an overhead valve internal combustion engine to the corresponding...

the single cam lobe and follower/rocker arm of a conventional engine is replaced with a locking multi-part rocker arm and two cam profiles: one optimized...

pushrod pushes on the rocker arm, which opens the valve. Depending on the design used, the valves are actuated by a rocker arm, finger, or bucket tappet...

A rocker cover (UK), valve cover elsewhere) is a cover that encloses the rocker arm in an internal combustion engine, bolting with a gasket seal to the...

controlled by one rocker arm, which is operated by the camshaft. Each rocker arm has a slipper follower mounted to the rocker arm with a spring, allowing...

sliding friction between the cam and rocker arm and therefore may have greater wear. The contact points on most Ducati rocker arms are hard-chromed to reduce...

system using engine oil which transfers the motion of the fuel injector rocker arm to the engine's exhaust valve(s). When activated, the exhaust valve opens...

Look up Rocker, Rockers, rocker, or rockers in Wiktionary, the free dictionary. Rocker or rockers may refer to: Rocker, Montana, a neighborhood in Butte...

sealable cylindrical rocker arm shafts protruded forwards through the front surfaces of the boxes, operating the now fully exposed rocker arms with the exposed...

marked rocker arm that mates with it. New IN1 rocker arms can also be identified by a Green painted mark on the top of the rocker arm. The IN2 rocker arms...

high-lift cam. Each of the intake valves is operated by a low-lift cam and rocker arm, while placing a T-lever between them allows the valves to follow the...

The system consists of a mechanical lifter mechanism that uses a second rocker arm to push the valve closed. Emanuel, Dave (1995). Big-Block Chevy Performance...

Daihatsu Sigra, Kunci Utamanya di Roller Rocker Arm" [Daihatsu Sigra's 3NR-VE Engine Technology, Roller Rocker Arm is the Key]. GridOto.com (in Indonesian)...

eccentric control shaft inside the rocker arm. By rotating the eccentric control shaft, the position of rocker arm is shifted, changing the swing angle...

camshaft acts onto a rocker arm that actuates the valves, an engine with Valvetronic has an intermediate arm between the rocker and the camshaft, which...

handle near the outer edge of the rotary part being the crank and human arm powering the rotation would be the connecting rod. However according to F...

the camshaft now lifts the valve directly via tappet instead of using a rocker arm. The exhaust valve is 1mm larger in diameter and the inlet manifold is...

valve Positive crankcase ventilation valve (PCV valve) Pulley part Rocker arm Rocker cover Starter motor Starter pinion Starter ring Turbocharger and Supercharger...

roller-bearing rocker arms are used to help reduce friction and improve engine efficiency, except the secondary intake valve rocker arm does not have a...

(replacing rocker arm actuation with tappets). SOHC engines were widely from the 1960s to 1990s. (eliminating pushrods but still utilizing rocker arms) Double...

A shishi-odoshi breaks the quietness of a Japanese garden with the sound of a bamboo rocker arm hitting a rock....

John Loy Rocker (born October 17, 1974) is an American former professional baseball relief pitcher who played six seasons in Major League Baseball (MLB)...

actuates the valve via a rocker mechanism (in an overhead valve (OHV) engine); via direct contact with the valve stem or rocker arm (in an overhead camshaft...

head and complex rocker arm geometry in both cam-in-block and single overhead cam engines (dual overhead cam engines may not have rocker arms). This adds...

pin that locks the high lift, high duration rocker arm to an adjacent low lift, low duration rocker arm(s). Many production VVT systems are the cam phasing...

structure. Needle bearings are heavily used in automobile components such as rocker arm pivots, pumps, compressors, and transmissions. The drive shaft of a rear-wheel...

camshaft and tappet is achieved by turning a set screw in the end of the rocker arm that contacts the end of the pushrod until a desired gap is achieved using...

lifter Camshaft Chest Combustion chamber Compression ratio Head gasket Rocker arm Timing belt Valve Forced induction Blowoff valve Boost controller Intercooler...

lifter Camshaft Chest Combustion chamber Compression ratio Head gasket Rocker arm Timing belt Valve Forced induction Blowoff valve Boost controller Intercooler...

cross-flow design, the intake and exhaust valves are opened and closed by the rocker arm driven by a camshaft timing belt. The two intake and two exhaust valves...