In telecommunication, call setup is the process of establishing a virtual circuit across a telecommunications network. Call setup is typically accomplished...

setup in Wiktionary, the free dictionary. Setup (the noun) or set up (the verb) may refer to: Set Up (2005 film), a 2005 Hong Kong horror film Setup (2011...

circuit may be used, it must be established between network nodes in the call setup phase. Once established, a bit stream or byte stream may be exchanged...

had hung up (dropped calls). This fraction is usually measured as a percentage of all calls. A call attempt invokes a call setup procedure, which, if...

call entered the exchange the route by which the call left the exchange call type (voice, SMS, etc.) voice call type (call setup, call continue, call...

was designed to provide a signaling and call setup protocol for IP-based communications supporting the call processing functions and features present...

packets. T.38 is not a call setup protocol, thus the T.38 devices need to use standard call setup protocols to negotiate the T.38 call, e.g. H.323, SIP &...

telephone company sends a sequence of typically four to ten digits during call setup. Direct inward dial (DID) service also provides DNIS. For example, a company...

SIP is more commonly used in personal consumer videophones. A number of call-setup methods based on instant messaging protocols such as Skype also now provide...

is the ITU-T address format of the X.25 protocol suite used as part of call setup to establish a switched virtual circuit between public data networks (PDNs)...

(VoLTE). Call setup time is faster than VoLTE due to the inherent lower latency of 5G NR. 5G VoNR removes the LTE anchor allowing the voice call to stay...

When the user tries to set up a call using an emergency number known by a GSM or 3G phone, the special emergency call setup takes place. The actual number...

which use CCS7 packet-switched signalling protocol to communicate the call setup and control information and use TDM to transport the actual circuit data...

signaling) or a separate band (out-of-band signaling) to the payload. Call setup will be comparatively slower since signaling channels are shared thus...

System No. 5 and earlier systems use in-band signaling, in which the call-setup information is sent by generating special multi-frequency tones transmitted...

channel (LAPD). There are 5 modes of PLP: call setup, data transfer, idle, call clearing, and restarting. Call setup mode is used to create VCs (virtual circuits)...

The multiple-camera setup, multiple-camera mode of production, multi-camera or simply multicam is a method of filmmaking, television production and video...

that provide the call service function and the bearer control function. The call service function uses BICC signaling for call setup and may also interwork...

phone sends a call setup request message to the mobile phone network via the nearest mobile phone base transceiver station (BTS). The call setup request message...

a number of attempts to perform a procedure or task. It may refer to: Call setup success rate When success refers to attempts to induce pregnancy, then...

in the network and therefore do not require the use of addresses for call setup. PVCs are identified at the subscriber interface by their logical channel...

deals with the challenges of traditional telephony such as switching and call setup. Most cellular network routing issues in different cells can be attributed...

connection setup and breakdown. Like TCP, Q.931 documents both the protocol itself and a protocol state machine. Q.931 was designed for ISDN call establishment...

Cochin, Kerala, India Call setup success rate, a term used in telecommunications denoting the percentage of the attempts to make a call which result in a...

disengagement because of preemption, or inadvertently due to system malfunction. Call setup Clearing (telecommunications) (a.k.a. teardown) Signaling System 7 Martin...

most cases, a single 64 kbit/s channel is sufficient to handle the call setup and call clear-down traffic for numerous bearer (voice and data) channels...

land lines, and handle billing and call setup. What really separated AMPS from older systems is the "back end" call setup functionality. In AMPS, the cell...

signaling in two-frequency mode with 2400Hz, for line seizure during call setup, and for tear-down. 2600Hz signaling was a standard for many international...

Endpoint A sends Q.931 call setup messages to endpoint B. Endpoint B sends the Gatekeeper an ARQ, asking if it can answer call. Gatekeeper returns an...

timeslot (TS16) is often reserved for signalling purposes, to control call setup and teardown according to one of several standard telecommunications protocols...