electronics, desoldering is the removal of solder and components from a circuit board for troubleshooting, repair, replacement, and salvage. Desoldering tools...

prior to resoldering — desoldering braids (or wicks) or vacuum desoldering equipment (solder suckers) can be used. Desoldering wicks contain plenty of...

tools for soldering are: contact soldering irons; desoldering tweezers or SMD hot tweezers; desoldering gun; hot air gun; infrared heater. Soldering iron...

pickup tool, and a soldering head; a desoldering station will have a desoldering head with vacuum pump for desoldering through-hole components, and a soldering...

refinish of a printed circuit board (PCB) assembly, usually involving desoldering and re-soldering of surface-mounted electronic components (SMD). Mass...

probes. Desoldering the chips is done carefully and slowly, so that the heat does not destroy the chip or data. Before the chip is desoldered the PCB...

soldering iron. Without developed skill, when manually soldering or desoldering a component, it is easy to accidentally reflow the solder of an adjacent...

weight: 49% Bi, 18% Pb, 21% In, 12% Sn. It is also known as ChipQuik desoldering alloy. and Lens Alloy 136, used for mounting lenses and other optical...

widely used in the electronics industry as a method of soldering and desoldering components onto circuit boards. Hot plates with two heating surfaces...

electronic devices while simultaneously heating them, for soldering or desoldering. Tweezer probes are a pair of electrical test probes fixed to a tweezer...

melting point, close to that of the material itself, to prevent the joint desoldering during firing in the enameling process. The remaining solder types are...

CPU can be overclocked to higher frequencies by either soldering or desoldering certain zero-ohm resistors on the logic board. An ATI Radeon 9200 graphics...

damaged mechanically. The unit does not have enough power for effective desoldering of many board- and chassis-mounted components. The design of the tip...

referred to as Teflon bone folders. PTFE is commonly used for the tip of desoldering pumps due to its high melting temperature. While PTFE is stable at lower...

powered off. These batteries had a limited lifespan and needed to be desoldered for replacement. The SRAM chips were later phased out in favor of the...

devices required to support 8 MB. Earlier revisions of the A5000 required desoldering of the fitted MEMC1a to provide such a socket. In 1992, Acorn introduced...

may require decapping or desoldering of integrated circuit chips from the circuit board of the device they own. A desoldered IC is placed into a chip...

conductive part of the pin, slicing the PCB traces, or on some cards, desoldering surface mount resistors. Apple Displays HDI-45 connector (a previous...

limited reuse may be possible, more than a few cycles of soldering and desoldering are likely to render both the components and the board unusable. In contrast...

particles into the air that can travel hundreds-to-thousands of miles. Desoldering is a technique used to extract higher-value materials like gold and silver...

Various SMD chips, desoldered...

motherboard, which requires partial dis-assembly of the computer and desoldering a part with several pins; many companies charge a considerable sum for...

7Bi33.3 72.7 In61.7Bi30.8Cd7.5 62 Cd Yes Bi56Sn30In14 79 91 Yes ChipQuik desoldering alloy, lead-free In51.0Bi32.5Sn16.5 60.5 Yes Yes Field's metal Bi50.0Pb25...

low-temperature physics. Bi 49, Pb 18, In 21, Sn 12 58 °C (136 °F) ChipQuik desoldering alloy. Cerrolow 136. Slightly expands on cooling, later shows slight...

removing socketed components on very early Electron models, but required desoldering work and therefore benefited from a fitting service for later units....

increase of Au content can increase melting point by 30 °C), subsequent desoldering requires higher temperature. Forms a mixture of two brittle intermetallic...

of the cover using a milling machine, saw blade, using hot air or by desoldering and cutting. The process can be either destructive or non-destructive...

since replacing them required partial dismantling of the camera body and desoldering the battery from a flexible circuit board. The camera will still operate...

or no signal from the coaxial connector. This is easily repairable by desoldering the tuner shield and re-flowing new solder to each connection inside...

thermistor that it also encloses. The positive and negative wires can be desoldered from their tabs, minding the iron tip does not make contact with the cell...