A circlip (a portmanteau of "circle" and "clip"), also known as a C-clip, snap ring, or Jesus clip, is a type of fastener or retaining ring that consists...

structure together". Circle cotter – Ring type of retaining component Circlip – Type of fastener or retaining ring Clevis fastener – Fastener consisting...

cotter lobster clasp cleco clip Binder clip Bulldog clip Crocodile clip circlip Clothespin hairpin clip paper clip terry clip clutch drawing pin (thumbtack)...

after the Channellock brand Locking pliers, also known as a vise-grip Circlip pliers, for fitting and removing retaining rings Round-nose pliers, for...

the outside or inside of a tube or pipe etc. This canal may receive a circlip, an o-ring, or a gasket. A depression on the entire circumference of a...

Herringbone gear Fastener Screw Screw thread Nut Clevis fastener Retaining ring Circlip E-ring Split pin cotter pin) Linchpin R-clip Rivet Tapered pin O-ring Belt...

type joint. The tripod is splined to the intermediate shaft and held by a circlip. A ball, supported on needle roller bearings, is fitted to each post of...

Mounting Piston Piston pin and crank pin Piston pin bush Piston ring and circlip Poppet valve Positive crankcase ventilation valve (PCV valve) Pulley part...

equipment Crocodile clip, or alligator clip, a temporary electrical connector Circlip, a semi-flexible metal ring fastener for holding a pin in place Roach clip...

multiple meanings of this term as an ironic running joke and deux ex machina. Circlip, also known as a "Jesus clip" Linchpin A failure of the Jesus nut is not...

splined and fits into the outer "joint". It is typically held in place by a circlip. The Birfield joint is a type of constant-velocity joint based on the Rzeppa...

nuts, low type Active DIN 471 Circlips (retaining rings) for shafts; Normal type and heavy type Active DIN 472 Circlips (retaining rings) for internal...

and the journal in the piston. The gudgeon pins are usually secured with circlips. No interference fit is used in any instance and the pin 'floats' entirely...

referred to as spirol pins - pronounced ‘spiril’ in the Birmingham area. Circlip – Type of fastener or retaining ring Split pin – Metal fastener with two...

sideways and the ends of the pin digging into the cylinder wall, usually by circlips. Gas sealing is achieved by the use of piston rings. These are a number...

perceived colour, particularly of blood. Blinders are held in position with a circlip arrangement or lugs into the nares of the bird, or a pin which pierces...

portion acts as a shoulder which retains the specific component or assembly. Circlips are a type of retaining ring. Circular push-on retaining rings may be installed...

reversing the takedown screw's orientation. Internally, the Mark II employs circlips to retain various pins instead of keeper screws, and as a result the internals...

retainer vary depending on which piston head retention system is used. If a circlip (or any non-preloaded system) is used, the force acting to separate the...

small, plastic circlips, the body of which passes between the maxilla and mandible of the beak and are held in place by the ends of the circlip being placed...

axles with axle retained in the housing at their inner ends typically with circlips which are 3¾-round hardened washers that slide into grooves machined at...

machines only). A700, A700D. A701.: 354–375  Bayonet with circular spring ("circlip beater"). A701A, A901/E/P, KM200/300/400/560 series and Titanium KM001/003: 376–385 ...

until it was bought in 1997–98 by Ellison's Holdings plc, which produced circlips, rings and fasteners for the automotive industry and who had previously...

For both spectacles and blinders, there are versions held in place by circlips in the nares of the bird, or others in which a pin pierces the nasal septum...

Seager Segger (surname) Object names Seeger ring, alternative name for a circlip The closest modern named object that corresponds to a seaspear is a harpoon...

slotted steel retaining cup which in turn is held in place by a steel circlip located in a shallow groove in the interior piston wall. This arrangement...

upper side of the connecting rod. The piston journals are secured with two circlips and are bathed in oil. A heat resistant light-metal-alloy is used for the...

pushrods.The valve springs can be replaced without removing the head because circlips on the valve stem prevent them falling.Engine accessories were mounted:...

cart-groove marks. Between 1960 and 1997, Harden's biggest employer was Ellison Circlips. The huge factory adjoined another smaller factory producing similar products...