partially melt at the solidus temperature (TS or Tsol), and fully melt at the higher liquidus temperature (TL or Tliq). The solidus is always less than...

the fraction of liquid and solid phases for a given binary composition and temperature that is between the liquidus and solidus line. In an alloy or a...

advantages when applied to soldering: the liquidus and solidus temperatures are the same, so there is no plastic phase, and it has the lowest possible melting...

having a marked difference between liquidus and solidus temperatures. It is often being removed by subsequent annealing and/or hot-working. It is exploited...

between its liquidus and solidus (or liquidus and eutectic temperature), so that it is in a "mushy" state. This allows for more complex parts and thinner...

nepheline, sodalite, phlogopite mica, and apatite may be present in the groundmass. Basalt has high liquidus and solidus temperatures—values at the Earth's...

metal between its liquidus and solidus temperature, ideally 30 to 65% solid. The mixture must have low viscosity to be usable, and to reach this low viscosity...

temperature range between the solidus and the liquidus), which leads to small pockets of liquid trapped throughout and ultimately porosity. These castings...

solid and liquid phases, mixtures can either have a single melting point, known as congruent melting, or they have different liquidus and solidus temperatures...

forming a eutectic—or by sintering at a temperature between the liquidus and solidus. Additionally, since the softer phase is generally the first to melt...

magma. Gabbro may have a liquidus temperature near 1,200 °C, and the derivative granite-composition melt may have a liquidus temperature as low as about...

magma lies between the solidus, which is defined as the temperature at which the magma completely solidifies, and the liquidus, defined as the temperature...

the solidus. In engineering and metallurgy, flux is a substance, such as salt, that produces a low melting point (liquidus) mixture with a metal oxide...

substance in question. The solidus is the temperature below which the substance is stable in the solid state. The liquidus is the temperature above which...

remains or to study archaeological materials. Using DTA one can obtain liquidus & solidus lines of phase diagrams. Bhadeshia, H.K.D.H. "Thermal analyses techniques...

reaches to liquidus temperature and then freezing range starts. At solidus temperature, the molten alloy becomes solid. Garland, Nibler, and Shoemaker...

solder. Tin forms intermetallics such as Cu6Sn5 and Ag3Cu that dissolve into the Tin liquidus or solidus (at 50 °C), stripping surface coating or leaving...

example, in the silver-gold system the melt temperature (liquidus) and freeze temperature (solidus) "meet at the pure element endpoints of the atomic ratio...

statistical analysis, liquidus temperatures, ternary property diagrams Phase Equilibria Diagrams: Phase diagrams, including liquidus and solidus temperatures,...

Argentium 935, Argentium 940 and Argentium 960 alloys exceed the standard required for hallmarking as sterling silver, and Argentium 960 silver meets the...

there are two lines, representing the solidus and liquidus. ASM Handbook. Properties and Selection Nonferrous Alloys and Special-Purpose Materials. V.2. USA:...

interface, and so compositions from the phase diagram are valid Solidus and liquidus are straight segments The fourth condition (straight solidus/liquidus segments)...

composition of 95wt% of In and 5wt% of Bi. The liquidus line of this composition occurs at 423 K (150 °C; 302 °F), and the solidus line at 398 K (125 °C;...

begins for a mixture is known as the solidus while the temperature where melting is complete is called the liquidus. Eutectics are special types of mixtures...

ladle and poured into a sample cup with a thermocouple embedded in it. The temperature is then monitored, and the phase diagram arrests (liquidus, eutectic...

temperature, pressure or mechanical loads. Inconel alloys are oxidation- and corrosion-resistant. When heated, Inconel forms a thick, stable, passivating...

of those components, and coincides with the freezing point. Non-eutectic alloys can have markedly different solidus and liquidus temperatures, as they...

Ferrosilicon is an alloy of iron and silicon with a typical silicon content by weight of 15–90%. It contains a high proportion of iron silicides. Ferrosilicon...

temperature and pressure, with both having a strong influence on the process. The presence of volatiles has the potential to significantly reduce solidus temperatures...

with larger span of solidus/liquidus temperatures tend to melt through a "mushy" state, during which the alloy is a mixture of solid and liquid material....