Solids control is a process used in drilling rigs which use drilling fluid. It involves separating the "cuttings" (drilled material) from the fluid, allowing...

the well, and the solids that are removed by the screen would be discharged out of the tank, and the drilling fluids with smaller solids would flow through...

and the larger the size of the solids removed. A desander with a 10 inches (250 mm) cone is able to remove 50% of solids within the 40-50μm range at a...

suitable for high pressure applications Large solids or debris may clog the pump An oilfield solids control system needs many centrifugal pumps to sit on...

Timaeus, that the classical elements were made of these regular solids. The Platonic solids have been known since antiquity. It has been suggested that certain...

excreted by fish the solid waste must also be treated, this is done by concentrating and flushing the solids out of the system. Removing solids reduces bacteria...

earthen pits were used as settling area to separate solids and mud thereby acting as a solids control equipment. Now, with the stringent environmental regulations...

position of the atoms. These solids are known as amorphous solids; examples include polystyrene and glass. Whether a solid is crystalline or amorphous...

invade the formation, depending on mud solids size: Use bridging agents to block large openings so mud solids can form a seal. For effectiveness, bridging...

be confused with settleable solids, also abbreviated SS, which contribute to the blocking of sewer pipes. Suspended solids are important as pollutants...

by dilution or solids control equipment such as an industrial centrifuge, desilter, desander and shale shaker . Mud weight use to control the trapped fluids...

vehicles customarily used for commercial satellites and major space probes. Solids are, however, frequently used as strap-on boosters to increase payload capacity...

the solids must be small enough to survive filtration through a filter with 2-micrometer (nominal size, or smaller) pores. Total dissolved solids are...

low-temperature properties of glassy solids are well understood on the fundamental physics level. Amorphous solids is an important area of condensed matter...

Retrieved August 25, 2020. "The Solids by The Solids - iTunes page". iTunes. 24 January 2008. Retrieved March 1, 2011. Official website The Solids at IMDb...

deposited into the mud tanks where other solid control equipment begin to remove the finer solids from it. The solids removed by the shale shaker are discharged...

for example, a solid ball consists of a sphere and its interior. Solid geometry deals with the measurements of volumes of various solids, including pyramids...

group of each solid were derived from the Platonic solids, resulting from their construction. Some sources say the Archimedean solids are synonymous...

Mixed liquor suspended solids (MLSS) is the concentration of suspended solids, in an aeration tank during the activated sludge process, which occurs during...

definitions of cocoa solids include all cocoa ingredients (cocoa mass, cocoa powder and cocoa butter). In this case, cocoa solids without cocoa butter...

A mud gun is designed for use in a solids control system of a drilling rig. It is a tool which is mainly used for mixing drilling mud in the circulatory...

through separation of solids from liquids, usually by sedimentation. By progressively converting dissolved material into solids, usually a biological...

Control rods are used in nuclear reactors to control the rate of fission of the nuclear fuel – uranium or plutonium. Their compositions include chemical...

dr.} Solid of revolution demonstration When a curve is defined by its parametric form (x(t),y(t)) in some interval [a,b], the volumes of the solids generated...

Solid modeling (or solid modelling) is a consistent set of principles for mathematical and computer modeling of three-dimensional shapes (solids). Solid...

solid state relay (SSR) is an electronic switching device that switches on or off when an external voltage (AC or DC) is applied across its control terminals...

a mixture of denser solids suspended in liquid, usually water. The most common use of slurry is as a means of transporting solids or separating minerals...

drilling and intervention; premium drill pipe and drill stem accessories; solids control and waste management equipment and services; drilling and completion...

In machining, numerical control, also called computer numerical control (CNC), is the automated control of tools by means of a computer. It is used to...

affect the solid content of the separated solids. Optimum residence time of solids in the centrifuge and the water content of the separated solids can be...