A casting defect is an undesired irregularity in a metal casting process. Some defects can be tolerated while others can be repaired, otherwise they must...
19 KB (2,461 words) - 09:10, 17 September 2023
Sand casting, also known as sand molded casting, is a metal casting process characterized by using sand—known as casting sand—as the mold material. The...
48 KB (6,827 words) - 02:27, 16 August 2024
After the shakeout of the casting it is inspected for defects. The most common defects are misruns and cold shuts. These defects can be caused by cold dies...
38 KB (4,630 words) - 03:06, 9 October 2024
Pulldown may refer to: Pulldown (casting), a type of casting defect Pull-down resistor, a type of resistor use Pull-down assay, a biochemical protein extraction...
628 bytes (111 words) - 22:33, 29 January 2019
the casting process. The main types are: gas porosity, shrinkage defects, mold material defects, pouring metal defects, and metallurgical defects. Casting...
47 KB (6,249 words) - 21:50, 13 June 2024
temperature Recombination hotspot, a region in a genome Hot spot (casting), a metal casting defect Hot Spot (cricket), an infrared tracking system Airport hot...
3 KB (359 words) - 19:39, 10 July 2024
primarily involved in setting up peering exchanges Pipe (casting), a type of metal-casting defect Boatswain's pipe, an instrument used for signalling or...
3 KB (444 words) - 02:31, 8 September 2024
inventory due to theft, damage, spoilage, etc. Shrinkage defect or shrinkage void, a casting defect caused by metal solidifying from the outside inward Shrinkage...
1,020 bytes (140 words) - 21:21, 3 April 2022
Veining (metallurgy) (category Casting (manufacturing))
a sheet like casting defect, produced by molten metal penetration into a sand casting mould. Veining a defect on the surface of a casting appearing as...
4 KB (396 words) - 20:41, 13 August 2024
Steel-Slab Casting Mold and Defect Formation' - JOM Online". The Minerals, Metals, and Materials Society. Retrieved 2014-03-29. "'Analyzing Casting Problems...
29 KB (4,129 words) - 02:14, 9 May 2024
Canada Blowhole Diversion Tunnel in Victoria, Australia A type of casting defect in metalworking Category:Blowholes This disambiguation page lists articles...
530 bytes (109 words) - 07:13, 11 November 2022
Investment casting is an industrial process based on lost-wax casting, one of the oldest known metal-forming techniques. The term "lost-wax casting" can also...
26 KB (3,201 words) - 21:30, 11 September 2024
Foundry (section Casting process simulation)
to remove harmful gases and elements from the molten metal to avoid casting defects. Material is added during the melting process to bring the final chemistry...
18 KB (2,362 words) - 19:52, 27 May 2024
Number. The presence of iron in aluminum helps in the decrease of casting defects, improves tensile, yield, hardness, and maintains strength at high...
5 KB (386 words) - 21:34, 1 April 2024
Alumina can react with silica to form mullite. Veining (metallurgy), sand casting defect associated with the alpha to beta silica phase change "Ceramic Faults...
3 KB (439 words) - 15:03, 15 August 2024
patterns, and potential defects in the casting before the start of the actual production process. By simulating the casting process, manufacturers can...
22 KB (2,902 words) - 05:27, 2 August 2024
Porosity sealing (category Casting (manufacturing))
from sub-micron to voids greater than 10 mm, depending on the casting. Casting defects caused by porosity can affect the part’s structural integrity,...
11 KB (1,346 words) - 20:41, 16 January 2024
in Weimar, Texas when the meter exploded, injuring one of the men. A casting defect in the meter was determined to be the cause of the explosion. May 17...
98 KB (10,602 words) - 11:25, 10 October 2024
only happened because the previous drop had initiated a crack from a casting defect, that the crack would have been detected by inspection after the drop...
55 KB (7,216 words) - 03:24, 25 March 2024
of a rat Rattail, fish of the family Macrouridae Rattail (casting), a defect in metal casting Rattail (haircut) Rattail skate (Dipturus lanceorostratus)...
598 bytes (97 words) - 03:45, 8 December 2020
Core (manufacturing) (redirect from Core (casting))
should also be minimized because they can cause casting defects or create weak spots in the casting. It is usually more critical to ensure the upper...
11 KB (1,548 words) - 14:26, 2 March 2024
of minerals distinct from the surrounding rock Vein (metallurgy), a casting defect Vein (band), an American metalcore band Vein (Boris album), 2006 Vein...
920 bytes (143 words) - 23:40, 5 February 2024
the 'M' shown in De Aetna which, whether intentionally or due to a casting defect, had no serif pointing out of the letter at top right. This form was...
135 KB (14,451 words) - 21:37, 24 September 2024
misadventures of the eponymous anthropomorphic dog Buckle (casting), a type of casting defect Buckle (clothing retailer) Buckle, a type of cobbler (food)...
1 KB (175 words) - 17:30, 27 October 2020
Slip casting, or slipcasting, is a ceramic forming technique, and is widely used in industry and by craft potters to make ceramic forms. This technique...
18 KB (2,020 words) - 04:14, 2 July 2024
An entrainment defect is a term used in metallurgy to describe a defect created in a casting by the folding-over of the oxidized surface layer of the...
2 KB (271 words) - 21:34, 12 June 2022
the two pieces without visible seam failed. The two pieces both show casting defects as well. Unsuccessful attempts to transfer Geometric small scale sculpture...
3 KB (362 words) - 20:21, 17 February 2024
['Remarriage' Song Joong-ki transforms into a North Korean defector..'Loh Kiwan' casting lineup revealed [Official]] (in Korean). Star News. Retrieved...
8 KB (753 words) - 10:54, 26 September 2024
Hydrogen gas porosity (category Casting (manufacturing))
Hydrogen gas porosity is an aluminium casting defect in the form of a porosity or void in an aluminium casting caused by a high level of hydrogen gas (H2)...
4 KB (600 words) - 20:51, 5 April 2021
Ingot (redirect from Ingot casting)
further processing. In steelmaking, it is the first step among semi-finished casting products. Ingots usually require a second procedure of shaping, such as...
10 KB (1,163 words) - 19:11, 24 March 2024