Control register

A control register is a processor register that changes or controls the general behavior of a CPU or other digital device. Common tasks performed by control registers include interrupt control, switching the addressing mode, paging control, and coprocessor control.

This section needs expansion with: dates for IBM, Intel and other vendors. You can help by adding to it. (May 2023)

The early CPU lacked dedicated control registers, and relied on a limited set of internal signals and flags.^[1] When IBM developed a paging version^{[note 1]} of the System/360, they added 16 control registers^[2][3] to the design for what became the 360/67. IBM did not provide control registers on other S/360 models, but made them a standard part^[4] of System/370, although with different register and bit assignments. As IBM added new features to the architecture, e.g., DAS, S/370-XA, S/370-ESA, ESA/390, they added additional fields to the control registers. With z/Architecture, IBM doubled the control register size to 64 bits.

On the 360/67, CR0 and CR2 are used by address translation, CR 4-6 contain miscellaneous flags including interrupt masks and Extended Control Mode,^[3] and CR 8-14^[5] contain the switch settings on the 2167 Configuration Unit.

Control Register 0 contains the address of the segment table for dynamic address translation.

Control register 2 is the Relocation exception address register.

CR4 is the extended mask register for channels 0-31. Each bit is the 1/0 channel mask for the corresponding channel.

CR5 is reserved for the extended mask register for channels 32–63. Each bit is the 1/0 channel mask for the corresponding channel.

CR6 contains two mode flags plus extensions to the PSW mask bits.

Control Register 8 contains the assignments of Processor Storage units 1–4 to central processing units (CPUs) and channel controllers (CCs).

Control Register 9 contains the assignments of Processor Storage units 5–8 to central processing units (CPUs) and channel controllers (CCs).

Control Register 10 contains the Processor storage address assignment codes.

Control Register 11 contains channel controller (CC) assignments.

CR12 contains I/O Control Unit Partitioning.

CR13 contains I/O Control Unit Partitioning.

CR14 contains indicators.

The control registers of ESA/390^[6] on the IBM S/390 are an evolutionary enhancement to the control registers on the earlier ESA/370,^[7] S/370-XA^[8] and S/370^[9] processors. For details on which fields are dependent on specific features, consult the Principles of Operation.^[10]

The control registers of z/Architecture^[11] are an evolutionary enhancement to the control registers of the earlier ESA/390 on the IBM S/390 processors. For details on which fields are dependent on specific features, consult the Principles of Operation.^[12] Because z/Architecture expands the control registers from 32 bits to 64, the bit numbering differs from that in ESA/390.

The CR0 register is 32 bits long on the 386 and higher processors. On x64 processors in long mode, it (and the other control registers) is 64 bits long. CR0 has various control flags that modify the basic operation of the processor. Register CR0 is the 32 Bit version of the old Machine Status Word (MSW) register. The MSW register was expanded to the Control Register with the appearance of the i386 processor.

Reserved, the CPU will throw a #UD exception when trying to access it.

Contains a value called Page Fault Linear Address (PFLA). When a page fault occurs, the address the program attempted to access is stored in the CR2 register.

Used when virtual addressing is enabled, hence when the PG bit is set in CR0. CR3 enables the processor to translate linear addresses into physical addresses by locating the page directory and page tables for the current task. Typically, the upper 20 bits of CR3 become the page directory base register (PDBR), which stores the physical address of the first page directory. If the PCIDE bit in CR4 is set, the lowest 12 bits are used for the process-context identifier (PCID).^[13]

Used in protected mode to control operations such as virtual-8086 support, enabling I/O breakpoints, page size extension and machine-check exceptions.

Reserved, same case as CR1.

Extended Feature Enable Register (EFER) is a model-specific register added in the AMD K6 processor, to allow enabling the SYSCALL/SYSRET instruction, and later for entering and exiting long mode. This register becomes architectural in AMD64 and has been adopted by Intel as IA32_EFER. Its MSR number is 0xC0000080.

CR8 is a new register accessible in 64-bit mode using the REX prefix. CR8 is used to prioritize external interrupts and is referred to as the task-priority register (TPR).^[14]

The AMD64 architecture allows software to define up to 15 external interrupt-priority classes. Priority classes are numbered from 1 to 15, with priority-class 1 being the lowest and priority-class 15 the highest. CR8 uses the four low-order bits for specifying a task priority and the remaining 60 bits are reserved and must be written with zeros.

System software can use the TPR register to temporarily block low-priority interrupts from interrupting a high-priority task. This is accomplished by loading TPR with a value corresponding to the highest-priority interrupt that is to be blocked. For example, loading TPR with a value of 9 (1001b) blocks all interrupts with a priority class of 9 or less, while allowing all interrupts with a priority class of 10 or more to be recognized. Loading TPR with 0 enables all external interrupts. Loading TPR with 15 (1111b) disables all external interrupts.

The TPR is cleared to 0 on reset.

XCR0, or Extended Control Register 0, is a control register which is used to toggle the storing or loading of registers related to specific CPU features using the XSAVE/XRSTOR instructions. It is also used with some features to enable or disable the processor's ability to execute their corresponding instructions. It can be changed using the privileged XSETBV read using the unprivileged XGETBV instructions.^[21]

There is also the IA32_XSS MSR, which is located at address DA0h. The IA32_XSS MSR controls bits of XCR0 which are considered to be "supervisor" state, and should be invisible to regular programs. It operates with the privileged XSAVES and XRSTORS instructions by adding supervisor state to the data they operate with. Put simply, if the X87 state was enabled in XCR0 and PT state was enabled in IA32_XSS, the XSAVE instruction would only store X87 state, while the privileged XSAVES would store both X87 and PT states. Because it is an MSR, it can be accessed using the RDMSR and WRMSR instructions.

• General-purpose register
• Test register
• Model-specific register
• Debug register
• Flag byte
• Status register

IBM manuals

M67prelim

System/360 Model 67 - Time Sharing System - Preliminary Technical Summary (PDF). Systems Reference Library (First ed.). IBM. C20-1647-0. Retrieved May 8, 2023.

M67

IBM System/360 Model 67 - Functional Characteristics (PDF). Systems Reference Library (Third ed.). IBM. February 1972. A27-2719-0. Retrieved May 8, 2023.

S/370

IBM System/370 - Principles of Operation (PDF) (Eleventh ed.). IBM. September 1987. GA22-7000-10. Retrieved May 8, 2023.

S/370-XA

IBM System/370 Extended Architecture Principles of Operation (PDF) (Second ed.). IBM. January 1987. SA22-7085-1. Retrieved May 8, 2023.

S/370-ESA

IBM Enterprise Systems Architecture/370 Principles of Operation (PDF) (First ed.). IBM. August 1988. SA22-7200-0. Retrieved May 8, 2023.

S/390-ESA

IBM Enterprise Systems Architecture/390 Principles of Operation (PDF) (Ninth ed.). IBM. June 2003. SA22-7201-08. Retrieved May 8, 2023.

z/Architecture

z/Architecture - Principles of Operation (PDF) (Fourteenth ed.). IBM. May 2022. SA22-7832-13. Retrieved May 8, 2023.

Wikibooks has a book on the topic of: X86 Assembly/Protected Mode

• Intel 64 and IA-32 Architectures Developer's Manual: Vol. 3A
• Intel 64 and IA-32 Architectures Software Developer Manuals
• Tech Docs: AMD64
• Wyatt's World: Cracking Open the Pentium III (1999-05-28)